Thyssenkrupp Destination Dispatch Elevators


Overview

This document outlines how to integrate a Mercury-Security EP or LP 4502 to the ThyssenKrupp Elevator System. The ThyssenKrupp integration supports up 128 total floors. When using front and rear entry points within the elevator cab, each entry point is considered to be a distinct destinations. A 32 story building using front and rear entry points requires a total of 64 destinations.

The ThyssenKrupp Elevators can only support one EP/LP 4502. In order to support multiple EP/LP 4502’s, a Primary and Secondary needs to be configured. The Primary EP/LP 4502 will manage communications to ThyssenKrupp. Communications between the ThyssenKrupp and the Secondary EP/LP 4502’s will have to go through the Primary EP/LP 4502. Primary and Secondary EP/LP 4502’s will exchange messages through an Over-Watch Controller Service.

Supported Reader Types

A traditional Mercury-based reader is used by the ThyssenKrupp elevator integration

Access It! Universal.NET Licensing
The following licensing option must be enabled within the Access It! Universal.NET dongle and is a system wide option.

  • Advanced Elevator Control - Yes
  • Integrated Reader x/x

Required Components

The following components are required to complete the integration:

  • Access It!® Universal.NET min s/w v7
  • EP/LP-4502-TKController min f/w 1.263
  • Plugable USB 2.0 Ethernet Adapter p/n USB2-E100 (EP) or USB2- OTGE100 (LP)

EP/LP-4502-TK Configuration

EP/LP Web Browser

  1. Install the Plugable Ethernet adapter to the EP/LP-4502
  2. Connect the Plugable USB 2.0 Ethernet adapter to the network
  3. On the EP/LP-4502 set S1 - Configuration DIP Switch DIP 2 ON
  4. On the EP/LP-4502 set S1 - Configuration DIP Switch DIPs 1, 3 & 4 OFF
  5. Apply power to the EP/LP-4502 controller
  6. Manually configure a computer to 192.168.0.100
  7. Using a crossover cable, connect computer to the on-board NIC of the EP/LP-4502
  8. Open a web browser and navigate to 192.168.0.251
  9. On the EP/LP-4502 set S1 - Configuration DIP Switch DIP 1 ON
  10. Click Click Here to Login
  11. Click Continue to this website (not recommended).
  12. Enter a Username of admin
  13. Enter a Password of password
  14. Click Network from the left hand menu
  15. Under the section Interface 1, select Use Static IP configuration:
    • IP Address: <Set accordingly>
    • Subnet Mask: <Set accordingly>
    • Default Gateway: <Set accordingly>
  16. Under the section Interface 2, select Use Static IP configuration:
    Interface 2 is used to communicate to the ThyssenKrupp system and must be in the same subnet as ThyssenKrupp elevator controller.
    • IP Address: 192.168.0.250
    • Subnet Mask: 192.168.0.250
    • Default Gateway: <Set accordingly>
  17. Click Accept
  18. Click Host Comm from the left hand menu
  19. Within the Data Security drop list, select TLS if Available
  20. Click Accept
  21. Click Auto-Save from the left hand menu
  22. Set the Card Database Size accordingly
  23. Wait 60 seconds for EP/LP controller to reboot
  24. Remove power from the EP/LP controller
  25. Set all S1 - Configuration DIP Switch DIPs OFF
  26. Apply power to the EP/LP controller

Access It! Universal.NET

  1. Within Access It! Universal.NET, create a new IP Server Channel
  2. Within Access It! Universal.NET, create a new EP/LP-4502 with the specified amount of memory from the web configuration
  3. Configure the Comm tab to use the new Channel and the IP address added within the Interface 1 setting from the web configuration
  4. Select the Elevator Tab
  5. Enter the total number of destinations used by the ThyssenKrupp system
    A front and rear entry floor is considered two separate destinations.
  6. If the elevator cab has a front and rear entry door select (check) the option Elevator cabs have rear floors
  7. Enter the maximum number of cab access configurations
    Cab Access is applied to a card and defines which cabs an indivual can use. Cab Access Configuration can be created by clicking the Edit Configurations button.
  8. Select (check) the Primary ThyssenKrupp controller if this is the only ThyssenKrupp controller.
    Only one primary controller can be installed per site.
  9. Click Save

Reader Configuration

  1. Within Access It! Universal.NET, edit a reader installed under the EP/LP-4502
  2. Within the Access configuration drop list, select the ThyssenKrupp Elevator
  3. Configure the Floor code override as needed
  4. Select the Extended Feature tab
  5. Within the Extended feature type drop list, select the ThyssenKrupp feature type
  6. Enter the ES Group ID
  7. Enter the Landing IP
  8. Enter the Object ID
  9. Select if this reader controls the front, rear, or both doors
  10. Select (check) the PIN entry enabled to allow for PIN entry. This allows for a user to enter a PIN on the elevator system and have it sent to the Mercury controller. If a valid PIN is detected access will be granted.
  11. Select (check) the sleep mode to place the system into sleep mode
  12. Click Save

 Floor Code Configuration

  1. Navigate to the Floor Codes screen within the Configuration menu
  2. Click the New button on the toolbar
  3. Enter an appropriate floor code name into the Floor Code Name field
  4. Select a timezone to be assigned to the floor(s)
  5. Select the appropriate reader from the previous reader setup (Optional)
    When reader is selected the friendly name is displayed
  6. Select the floor(s) to be assigned to the floor code from the Available Floors list
  7. Move the selected floor(s) and timezone to the Assigned Floor / Assigned Timezone by clicking the > button. To move all the available floors to the Assigned Floor / Assigned Timezone with the current timezone selected, click the >> button
    To assign a different timezone to an already assigned floor, remove the assigned floor by selecting it from the Assigned Floor / Assigned Timezone and click the < button. Click the << button to remove all of the assigned floors to assign a different timezone to them.
  8. Click Save

Access Level Configuration

  1. Navigate to the Access Levels screen within the Configuration menu
  2. Click the New button on the toolbar
  3. Enter an appropriate access level name into the Access Level Name field
  4. Select the Elevator tab
  5. Select a floor code to be assigned to a reader
  6. Select the reader(s) to be assigned to the floor code from the Available Readers list
  7. Move the selected reader(s) to the Assigned Reader / Assigned FloorCode by clicking the > button. To move all the available readers to the Assigned Reader / Assigned FloorCode with the current floorcode selected, click the >> button
    To assign a different floorcode to an already assigned reader, remove the assigned reader by selecting it from the Assigned Reader / Assigned FloorCode and click the < button. Click the << button to remove all of the assigned readers to assign a different floorcode to them.
  8. Click Save

Card Configuration

  1. Within Access It! Universal.NET, create a new card or edit an existing card
  2. Select the Elevator tab
  3. Click New
  4. Assign the default floor number for the card
  5. Assign the default door
  6. Select the ThyssenKrupp Cardholder flags. Valid options are:
    • ADA - When presented, an ADA call is made to the Elevator
    • VIP-VIP operation allows them to swipe a card or enter a PIN to isolate the elevator and provide uninterrupted access to their designated floor.
    • Service Operation- Service personnel can use this function to call an empty elevator and ride it nonstop to their destination floor. The user simply registers a call via a card swipe or PIN entry that is pre-programmed to grant access
    • Code Blue Operation-Special elevator mode which is commonly found in hospitals. It allows an elevator to be summoned to any floor for use in an emergency situation.
    • Capture - Authorized users can select and recall specific elevators to specific floors using a kiosk or other destination input device. Once captured, the elevator car can be placed on independent service to give users control of the car to clean the interioror perform maintenance. This function canbe operated via PIN entry or card swipe. 
    • Express- Program selected elevators to be cycled continuously between two floors for a pre-determined duration. For example, this feature can help hotels transport food efficiently from their kitchen to a ballroom on another floor.You can also prevent other guests from boarding to provide your banquet guests with VIP treatment.
    • Service2 Operation-Service personnel can use this function to call an empty elevator and ride it nonstop to their destination floor. The user simply registers a call via a card swipe or PIN entry that is pre-programmed to grant access 
    • Service3 Operation- Service personnel can use this function to call an empty elevator and ride it nonstop to their destination floor. The user simply registers a call via a card swipe or PIN entry that is pre-programmed to grant access
  7. Select the ThyssenKrupp  car preference
  8. Click OK

  • 749
  • 11-Mar-2019
  • 92 Views