Bosch B/G Series Intrusion Panel Integration


Overview

The Bosch B/G series intrusion panel integration enables local workstations to monitor and interact with Bosch B/G series intrusion panels. Intrusion panel integration licenses must be purchased separately for each intrusion panel being monitored within the system.

Prior to configuring the integration, the following are required:

  • Access It! Universal.NET min s/w v6
  • Bosch B/G Series: B3512, B4512, B5512, B6512, B8512, and B9512

Access It! Universal.NET Licensing

The following licensing option must be enabled within the Access It! Universal dongle and is a system wide license. 

  • Intrusion Panels - 1/x

Panel Configuration

It is assumed that field technicians are familiar with the installation, servicing and RPS configuration software for the Bosch B/G series intrusion panels. All question regarding the Bosch RPS configuration software or the Bosch B/G series intrusion panels must be directed to Bosch Technical Support.

Prior to integrating, the following must be applied to the Bosch B/G intrusion panel:

  • Automation Device must be set to Mode 2, (formerly SDI Automation Address 80 enabled), in the RPS software. (see attached image below)

Software Configuration

Adding A Bosch B/G Series Intrusion Panel

  1. Navigate to the hardware tree by clicking on the hardware group within the Navigation pane
  2. Select Intrusion Panels item from the hardware tree
  3. Click New button on the toolbar
  4. Enter appropriate name for the panel
  5. Select Intrusion panel type of Bosch B/G Series Panels
  6. Enter appropriate IP address
  7. Enter appropriate TCP port
    Default port is 7700
  8. Enter appropriate Passcode
    Default Automation Passcode is Bosch_Auto
  9. Select appropriate panel model
  10. Select desired Arming Mode
  11. Click Save button to save and close Intrusion Panel properties

Creating Intrusion Panel Areas

By creating intrusion panel areas, friendly names are assigned to pre-programmed area numbers within the panel.

  1. Navigate to the hardware tree by clicking on the hardware group within the Navigation pane
  2. Select Intrusion Panels item from the hardware tree
  3. Select appropriate intrusion panel to be modified
  4. Select Areas tab from lower pane
  5. Click New button on the Areas tab toolbar
  6. Enter appropriate name for the Area name
  7. Enter appropriate Area number
  8. Click Save button to save and close Intrusion Area properties

Creating Intrusion Panel Ouputs

By creating intrusion panel outputs, friendly names are assigned to pre-programmed area numbers within the panel.

  1. Navigate to the hardware tree by clicking on the hardware group within the Navigation pane
  2. Select Intrusion Panels item from the hardware tree
  3. Select appropriate intrusion panel to be modified
  4. Select Outputs tab from lower pane
  5. Click New button on the Outputs tab toolbar
  6. Enter appropriate name for the Output name
  7. Enter appropriate Output number
  8. Click Save button to save and close Intrusion Output properties

Creating Intrusion Panel User Codes

  1. Navigate to the hardware tree by clicking on the hardware group within the Navigation pane
  2. Select Intrusion Panels item from the hardware tree
  3. Select appropriate intrusion panel to be modified
  4. Select User Codes tab from lower pane
  5. Click New button on the User Codes tab toolbar
  6. Click the ... button from within the User name field
  7. Enter a Last Name or Card Number
  8. Click the magnifying glass icon to search
  9. Select appropriate user from result list
  10. Click OK button to populate User name with the selected user
  11. Enter appropriate User number
  12. Click Save button to save and close Intrusion User Code properties

Creating Intrusion Panel Points

By creating intrusion panel outputs, friendly names are assigned to pre-programmed area numbers within the panel.

  1. Navigate to the hardware tree by clicking on the hardware group within the Navigation pane
  2. Select Intrusion Panels item from the hardware tree
  3. Select appropriate intrusion panel to be modified
  4. Select Points tab from lower pane
  5. Click New button on the Points tab toolbar
  6. Enter appropriate name for the Point name
  7. Enter appropriate Point number
  8. Click Save button to save and close Intrusion Point properties

Troubleshooting Errors

  1. The profile is not valid at this time: Valid date range is YYYY-MM-DD - YYYY-MM-DD. Panel time is YYYY-MM-DD hh:mm:ss
    1. Ensure that the system time within the Bosch panel is correct, and within the valid date range referenced within the error.
  2. Panel refused connection because it reached the maximum number of connections
    1. Ensure that there are no other connections being made it to Bosch panel (via RPS, Access It!, etc.)

  • 667
  • 21-Dec-2018
  • 1264 Views