Invixium Biometric Integration


Overview

The Invixium biometric integration allows for enrolling biometric templates into an Invixium reader via Access It! Universal.NET. When using this integration, the biometric template, as well as any biometric comparisons are performed by the reader. Prior to configuring the integration, the following are required:

  • Access It! Universal.NET min s/w v5.6 
  • Invixium IXM WEB min s/w v1.5.0.0
  • Invixium reader min f/w v1.5.0.0
    All Invixium readers except the MERGE CR are supported

Prior to configuring the IXM biometric integration, the IXM WEB software must be fully installed, licensed, and all biometric devices added. 

Access It! Universal.NET Licensing
The following licensing option must be enabled within the Access It! Universal.NET dongle and is a system wide license.

  • Biometric Support - Yes

Wiring

The Invixium readers should be wired to a Mercury-Security reader port using the standard Wiegand wiring. It is recommended the reader be powered over PoE or else a dedicated power supply (minimum 1A) must be used.

Invixium Reader SIO Reader Port
WDATA_OUT0 (green) D0
WDATA_OUT1 (white) D1
ACP_LED1 (brown) LED
WGND (black w/green) GND

The LED wire is required for panel feedback functionality. 

Configuring IXM WEB Database Synchronization
By default, every 30 seconds the IXM WEB syncs the databases between itself and the Access It! Universal.NET. To configure this database link:

  1. Log into IXM WEB
  2. Within page 2 of the home page, select Link
  3. Select RS2
  4. Enable the link by clicking the On/Off button located in the upper right-hand corner
    • Authentication Mode - Select the appropriate SQL Authentication mode used to connect to the AIUniversal database
    • Server - Enter the SQL Server name used by Access It! Universal
      Default SQL installations use an AIUniversal instance (SERVERNAME\AIUniversal)
    • Database - Use the database name AIUniversal
    • Interval - This value is how often the databases will sync. the default is 30 seconds
    • Sync Direction - Use the default option of bidirectional sync between IXM and RS2
    • Auto Transfer - Use the default option of All Users to All Devices
  5. Click Apply
  6. Click OK
  7. Click Sync Card Formats
  8. Click the Home Link to return to the home page

Configuring IXM WEB Panel Feedback
The Invixium reader reports Access Granted when a biometric template is successfully verified. If the credential is inactive within Access It! Universal.NET it can lead to user confusion when a reader reports "Access Granted" but the software displays "Access Denied". To prevent this, the Invixium reader can be configured to report "Access Granted" based on the feedback of the LED wire attached to the reader port of the Mercury-Security panel.
This functionality requires the LED wire be connected between Invixium reader and Mercury panel.

  1. Log into IXM WEB
  2. Select Config
  3. Select Panel Feedback
  4. Enable the Panel Feedback by clicking the On/Off button located in the upper right-hand corner
  5. Enable the LED Control By Panel function by clicking the Active/Inactive button
  6. Use the LED Mode One LED
  7. Click Apply
  8. Click the Home Link to return to the home page

Configuring IXM WEB Custom Card Formats
Invixium readers are configured to output 26 bit Wiegand and allow for the use of a custom Wiegand format. To create a new custom format:

An image outlining how to setup the RS2 stock 33 bit f/c 3 format can be found within KB article 640.

  1. Log into IXM WEB
  2. Select Config
  3. Select Wiegand
  4. Select the Manage Wiegand button located at the bottom of the page
  5. Select the card format to be used by the Invixium Readers within the Wiegand grid
  6. Select Selected from the Upload drop list
  7. Select (check) the device(s) to upload the format to
  8. Click OK
  9. Click the Wiegand Link to return to the Wiegand configuration page
  10. Set Output settings as follows:
    • Weigand
      • ID Type: Prox Card ID
      • Duress: <set accordingly>
    • Identification
      • Success: newly uploaded card format
      • Fail: <set accordingly>
    • Verification
      • Success: newly uploaded card format
      • Fail: <set accordingly>
  11. Click Apply
  12. Click OK
  13. Click the Home Link to return to the home page

Configuring Access It! Universal.NET for Invixium Enrollment

  1. Navigate to Workstations (System | Workstations)
  2. Edit the Invixium enrollment workstation
  3. Select the Encode/Enroll tab
  4. Click New
  5. Provide a friendly name for the Device name
    This name will be used in the Commands section for Cards to enroll the Invixium template.
  6. Select Invixium in the Device type drop list
  7. Enter the following URL, replacing IP Address and Port as needed:
    http://IXM_WEB_IP_ADDRESS:IXM_WEB_PORT/Link/EnrollRS2User/
    Sample URL: http://192.168.2.207:9108/Link/EnrollRS2User/
  8. Click OK
  9. Click Save on the Edit Workstation window
  10. Close Access It! Universal.NET
  11. Launch Access It! Universal.NET

Biometric Enrollment

  1. Navigate to Cardholders
  2. Search for a cardholder to enroll
  3. Select a card record
  4. From the commands ribbon, select the friendly name assigned to the Invixium enrollment command

  • 639
  • 17-Jul-2018
  • 1526 Views