Configuring The MR-51e For Access It! Universal


Overview

This document outlines the steps required to program a MR-51e module to obtain an IP address via Public DHCP (assigned by standard DHCP server), Static (manually assigned), or MSC-DHCP (assigned by EP SCP). The included utility MSC MR51e Address Configuration Tool is only used when assigning a static IP Address
Access It! Universal 3.0 or higher must be installed
The MR-51e must be running firmware revision 1.4.2 or higher.
The EP controller must be running firmware revision 1.147 or higher.

Public DHCP

The EP controller must be configured to use DHCP to obtain an IP address.

  1. Set S1 - Configuration DIP Switch DIP 1 ON
  2. Set S1 - Configuration DIP Switch DIPs 2, 3, & 4 OFF
  3. Apply power to the MR-51e or press S2 - Reset Switch
  4. Make note of the MAC address located on the side of the RJ-45 jack
  5. Run Access It! Universal
  6. From the File Menu, select Go | Main | Hardware
  7. Click the plus sign (+) to expand SCPs
  8. Click the plus sign (+) to expand the SCP the MR-51e will be installed on
  9. Select the SIOs branch, not the plus sign (+)
  10. A list of all available SIOs appear in the pane to the right of the hardware tree
  11. Edit the first uninstalled SIO from the right hand pane
    General Tab
    Model: MR-51E
    Device Installed: X
    IP Address: <NOT USED>
    MAC Address: < MAC Address of MR-51e>
    Click Save
    If unable to resolve the Host Name to an IP Address, contact your local network administrator.

Static

  1. Set S1 - Configuration DIP Switch DIPs 1 & 2 ON
  2. Set S1 - Configuration DIP Switch DIPs 3 & 4 OFF
  3. Open the included utility MR51e Address Configuration Tool
  4. Apply power to the MR-51e or press S2 - Reset Switch
    Once detected, the MR-51e will auto populate in the Devices in Programming Mode window
  5. Select the MR-51e to be programmed
  6. Static IP Address: Full 12 digit IP address of MR-51e
    If the desired IP address of the MR-51e is to be 192.168.1.15, then the IP address field must be entered as 192.168.001.015.
    Subnet Mask: Subnet Mask
    Default Gateway: Full 12 digit Gateway IP Address
  7. Click Assign Static Address~If assigned properly, the checkbox Address Assigned will be checked.
  8. Make note of the MAC address of the MR-51e
  9. Set S1 - Configuration DIP Switch DIP 2 ON
  10. Set S1 - Configuration DIP Switch DIPs 1, 3 & 4 OFF
  11. Apply power to the MR-51e or press S2 - Reset Switch
  12. Run Access It! Universal
  13. From the File Menu, select Go | Main | Hardware
  14. Click the plus sign (+) to expand SCPs
  15. Click the plus sign (+) to expand the SCP the MR-51e will be installed on
  16. Select the SIOs branch, not the plus sign (+)
  17. A list of all available SIOs appear in the pane to the right of the hardware tree
  18. Edit the first uninstalled SIO from the right hand pane
    General Tab~Model: MR-51E
    Device Installed: X
    IP Address: < Set accordingly>
    MAC Address: < MAC Address of MR-51e>
  19. Click Save

Panel DHCP

When using Panel DHCP, the MR-51e must be connected to the same physical switch as the EP controller.

  1. Set S1 - Configuration DIP Switch DIPs 1, 2, 3, & 4 OFF
    Alternately DIPs 1, 2, 3, & 4 ON
  2. Apply power to the MR-51e or press S2 - Reset Switch
  3. Make note of the MAC address located on the side of the RJ-45 jack
  4. Run Access It! Universal
  5. From the File Menu, select Go | Main | Hardware
  6. Click the plus sign (+) to expand SCPs
  7. Click the plus sign (+) to expand the SCP the MR-51e will be installed on
  8. Select the SIOs branch, not the plus sign (+)
  9. A list of all available SIOs appear in the pane to the right of the hardware tree
  10. Edit the first uninstalled SIO from the right hand pane
    General Tab
    Model: MR-51E
    Device Installed: X
    IP Address: <Set accordingly>
    MAC Address: < MAC Address of MR-51e>
  11. Click Save

  • 395
  • 20-Dec-2018
  • 5438 Views