Overview

This document outlines the steps required to program a MR-51e module to obtain an IP address via Public DHCP (assigned by standard DHCP server), Static (manually assigned), or MSC-DHCP (assigned by EP/LP SCP). The included utility MSC MR51e Address Configuration Tool is only used when assigning a static IP Address
Access It! Universal.NET 3.0 or higher must be installed
The MR-51e must be running firmware revision 1.4.2 or higher.
The EP/LP controller must be running firmware revision 1.147 or higher.

Public DHCP

The EP/LP controller must be configured to use DHCP to obtain an IP address.

1. Set S1 - Configuration DIP Switch DIP 1 ON
2. Set S1 - Configuration DIP Switch DIPs 2, 3, & 4 OFF
3. Apply power to the MR-51e or press S2 - Reset Switch
4. Make note of the MAC address located on the side of the RJ-45 jack
5. Run Access It! Universal.NET
6. From the File Menu, select Go | Main | Hardware
7. Click the plus sign (+) to expand SCPs
8. Click the plus sign (+) to expand the SCP the MR-51e will be installed on
9. Select the SIOs branch, not the plus sign (+)
10. A list of all available SIOs appear in the pane to the right of the hardware tree
11. Edit the first uninstalled SIO from the right hand pane
    General Tab
    Model: MR-51E
    Device Installed: X
    IP Address: <NOT USED>
    MAC Address: < MAC Address of MR-51e>
    Click Save
    If unable to resolve the Host Name to an IP Address, contact your local network administrator.

Static

1. Set S1 - Configuration DIP Switch DIPs 1 & 2 ON
2. Set S1 - Configuration DIP Switch DIPs 3 & 4 OFF
3. Open the included utility MR51e Address Configuration Tool
4. Apply power to the MR-51e or press S2 - Reset Switch
   Once detected, the MR-51e will auto populate in the Devices in Programming Mode window
5. Select the MR-51e to be programmed
6. Static IP Address: Full 12 digit IP address of MR-51e
   If the desired IP address of the MR-51e is to be 192.168.1.15, then the IP address field must be entered as 192.168.001.015.
   Subnet Mask: Subnet Mask
   Default Gateway: Full 12 digit Gateway IP Address
7. Click Assign Static Address~If assigned properly, the checkbox Address Assigned will be checked.
8. Make note of the MAC address of the MR-51e
9. Set S1 - Configuration DIP Switch DIP 2 ON
10. Set S1 - Configuration DIP Switch DIPs 1, 3 & 4 OFF
11. Apply power to the MR-51e or press S2 - Reset Switch
12. Run Access It! Universal.NET
13. From the File Menu, select Go | Main | Hardware
14. Click the plus sign (+) to expand SCPs
15. Click the plus sign (+) to expand the SCP the MR-51e will be installed on
16. Select the SIOs branch, not the plus sign (+)
17. A list of all available SIOs appear in the pane to the right of the hardware tree
18. Edit the first uninstalled SIO from the right hand pane
    General Tab~Model: MR-51E
    Device Installed: X
    IP Address: < Set accordingly>
    MAC Address: < MAC Address of MR-51e>
19. Click Save

Panel DHCP

When using Panel DHCP, the MR-51e must be connected to the same physical switch as the EP/LP controller.

1. Set S1 - Configuration DIP Switch DIPs 1, 2, 3, & 4 OFF
   Alternately DIPs 1, 2, 3, & 4 ON
2. Apply power to the MR-51e or press S2 - Reset Switch
3. Make note of the MAC address located on the side of the RJ-45 jack
4. Run Access It! Universal.NET
5. From the File Menu, select Go | Main | Hardware
6. Click the plus sign (+) to expand SCPs
7. Click the plus sign (+) to expand the SCP the MR-51e will be installed on
8. Select the SIOs branch, not the plus sign (+)
9. A list of all available SIOs appear in the pane to the right of the hardware tree
10. Edit the first uninstalled SIO from the right hand pane
    General Tab
    Model: MR-51E
    Device Installed: X
    IP Address: <Set accordingly>
    MAC Address: < MAC Address of MR-51e>
11. Click Save