NOTICE: Support for legacy Biometrics have been discontinued with the release of Access It! Universal.NET 9.0

---

Overview

The Biometric Gateway is a legacy SIO device that supports communication of up to eight Morpho 4G biometric readers. When using Access It! Universal with the optional biometric license, the Biometric Gateway requires the use of an external reader. Upon a valid transaction at the external reader, the Biometric Gateway will initiate the 4G reader’s verification polling.
The overall procedure when presenting a card at the external reader is as follows:

• A Card or PIN is presented at the external reader.
• The SCP controller recognizes that the external reader requires a biometric verification.
• The EP controller instructs the biometric gateway to initializes the 4G reader and the reader prompts for a finger to be presented.
• The fingerprint read is sent to the Biometric Gateway.
• the Biometric gateway translates the fingerprint template into a formatrecognizableto the SCPcontroller.
• The SCP controller compares the fingerprint read to the stored template within its database.
• If fingerprint comparison matches, the SCP controller grants access to the external reader.

Access It! Universal Licensing
The following licensing option must be enabled within the Access It! Universal dongle and is a system wide license.

• Biometric Support - Yes

Installation Requirements

The Biometric Gateway requires the following when using Morpho 4G devices:

• Access It! Universal min s/w v4
• Access It! Universal optional Biometric license enabled
• Biometric gateway min f/w rev 34
• Supported 4G readers
  • 4G V-FLEX Lite min f/w v4.4.6.0.3.a1.0
  • 4G V-FLEX min f/w 4.1.11.0.2.a2.0
  • 4G V-STATION min f/w 4.1.11.0.2.a2.0

Hardware Configuration

Biometric Gateway Jumper Settings

Jumper	Setting
J3	485
J4	485
J5	485
J6	485
J7	2W
J8 (SIO Termination)	Open/Closed (as needed for termination)
J9	485
J10 (SIO Termination)	Open/Closed (as needed for termination)
J11	Closed
J12	Closed
J13	Closed
.

Biometric Gateway Dip Switch Settings

Address	Dip 1	Dip 2	Dip 3	Dip 4	Dip 5	Dip 6	Dip 7	Dip 8
0	Off	Off	Off	Off	Off	On	On	On
1	On	Off	Off	Off	Off	On	On	On
2	Off	On	Off	Off	Off	On	On	On
3	On	On	Off	Off	Off	On	On	On
4	Off	Off	On	Off	Off	On	On	On
5	On	Off	On	Off	Off	On	On	On
6	Off	On	On	Off	Off	On	On	On
7	On	On	On	Off	Off	On	On	On
8	Off	Off	Off	On	Off	On	On	On
9	On	Off	Off	On	Off	On	On	On
10	Off	On	Off	On	Off	On	On	On
11	On	On	Off	On	Off	On	On	On
12	Off	Off	On	On	Off	On	On	On
13	On	Off	On	On	Off	On	On	On
14	Off	On	On	On	Off	On	On	On
15	On	On	On	On	Off	On	On	On
16	Off	Off	Off	Off	On	On	On	On
17	On	Off	Off	Off	On	On	On	On
18	Off	On	Off	Off	On	On	On	On
19	On	On	Off	Off	On	On	On	On
20	Off	Off	On	Off	On	On	On	On
21	On	Off	On	Off	On	On	On	On
22	Off	On	On	Off	On	On	On	On
23	On	On	On	Off	On	On	On	On
24	Off	Off	Off	On	On	On	On	On
25	On	Off	Off	On	On	On	On	On
26	Off	On	Off	On	On	On	On	On
27	On	On	Off	On	On	On	On	On
28	Off	Off	On	On	On	On	On	On
29	On	Off	On	On	On	On	On	On
30	Off	On	On	On	On	On	On	On
31	On	On	On	On	On	On	On	On

BIO-GW Gateway

BIO-GW Gateway	SCP / EP
TR1+	TR2 ~ TR3+
TR1-	TR2 ~ TR3-
GND	GND
.

Morpho 4G Reader

Morpho 4G Reader	BIO-GW Gateway
RS-485+	TR2+
RS-485-	TR2-
GND	GND
.

SecureAdmin

4G V-FLEX / 4G V-STATION

Prior to making any changes, the 4G reader must already be registered in SecureAdmin. Contact L1/Morpho for any registration inquiries.

1. Log into SecureAdmin
2. Select Device Settings
3. Select the 4G reader
4. Select the Communication tab
5. Set the Device ID accordingly
   Each 4G reader on the Biometric gateway must be uniquely addressed between 0 and 7.
6. Set the Host Protocol to RS-485
7. Set the Host Baud Rate to 38400
8. Click Apply
9. Select the Biometrics tab
10. Within the Device mode field, select Verify
11. Select the Template Type 1:1 TEM
12. In the Multi-User Verification set the Number of Users to 1
13. Click Apply
14. Select the Miscellaneous tab
15. In the Send verification Result section, ensure none of the checkboxes are checked
16. Check the box Activate Verification Polling Mode
17. Click Yes at the SecureAdmin warning dialog box
18. Select Weigand Only for the Initiate Verification By field
19. Click Apply
20. Close SecureAdmin

SecureAdmin Lite

4G V-FLEX Lite
Prior to making any changes, the 4G reader must already be registered in SecureAdmin Lite. Contact L1/Morpho for any registration inquiries.

1. Log into SecureAdmin Lite
2. Select Network
3. Select Network Tree
4. Select the 4G reader
5. Select the Communication tab
6. Set the Device ID accordingly
   Each 4G reader on the Biometric gateway must be uniquely addressed between 0 and 7.
7. Set the Host Protocol to RS-485
8. Set the Host Baud Rate to 38400
9. Click Apply
10. Select the Biometrics tab
11. Within the Device mode field, select Verify
12. Select the Template Type 1:1 TEM
13. In the Multi-User Verification set the Number of Users to 1
14. Click Apply
15. Close SecureAdmin Lite
16. Run the attached WeigandPollingMode.exe utility and connect to the 4G V-Flex Lite
17. Enable the Wiegand Polling Mode
18. Disconnect from the 4G V-Flex Lite
19. Close the WeigandPollingMode.exe utility

Access It! Universal.NET 5.2

1. Within Access It! Universal.NET navigate to the Hardware menu
2. Select SCPs
3. Edit the EP controller the Biometric reader is installed under
4. Select the Biometrics tab
5. Select Edit Biometric Types
6. Select New
7. Within the Biometric type description, enter the name Morpho 4G
8. From the Biometric template type, select Bioscrypt/Morpho Fingerprint
9. Select the Default security threshold
   • The default threshold determines the ratio of false rejects to false accepts.
     • Highest – Most Secure
     • Medium – Default Settings
     • Lowest – Least Secure
10. If needed, check the Store security threshold per user checkbox
11. Click OK
12. Click Save
13. Within the Hardware menu, select Installed Readers
14. Edit the reader that the 4G V-Flex Lite's RS-485 wiring is attached to
15. Select the Reader Settings tab
16. Set the Reader Type to Bioscrypt
17. Click Save
18. Edit the reader that the external reader is attached to
19. Select the Biometrics tab
20. Select the 4G V-Flex Lite reader from the Associated Biometric Reader list
21. Check the box Require Biometric Verification
22. Click Save

Configuring Enrollment Users

1. Within Access It! Universal.NET navigate to the Configuration menu
2. Select UserGroups
3. Edit a UserGroup responsible for enrolling fingerprint templates
4. Select the Permissions tab
5. Expand the Cardholder node
6. Select Biometrics
7. Ensure Full Access is selected within the right hand pane
8. Click Save
9. Select Users
10. Create a new or edit an existing user responsible for biometric enrollment
11. Assign the User to the modfied UserGroup
12. Click Save

Enrolling Biometric Template To New Cardholders

1. Within Access It! Universal.NET navigate to Main | Cardholders
2. Select New from the toolbar
3. During the New Cardholder/Card wizard there will be a step entitled Capture Biometric Information
4. Select Morpho/Bioscrypt
5. Select Capture Template
   Upon first time enrollment, click Setup... to configure communication parameters.
6. Present finger at the 4G V-Flex Lite reader
7. Remove Finger
8. Click Next to complete the new Cardholder/Card wizard

Enrolling Biometric Template To Existing Cardholders

1. Within Access It! Universal navigate to Main | Cardholders
2. Edit an existing cardholder
3. Select the Biometrics tab
4. Select Morpho/Bioscrypt
5. Select Capture Template
   Upon first time enrollment, click Setup... to configure communication parameters.
6. Present finger at the 4G V-Flex Lite reader
7. Remove Finger
8. Click Save

Access It! Universal 4x - 5.1.NET

Site Configuration

1. Within Access It! Universal navigate to System | Sites
2. Edit the Site that will be using the biometric option
3. In the Biometric Reader Type list select Bioscrypt
4. Click Save
   All SCPs within the site will be reset; during this time cards will stop working for up to 10 minutes.
5. Restart Access It! Universal for changes to take effect

Hardware Tree Configuration

1. Within Access It! Universal navigate to Main | Hardware
2. Select SCPs
3. Edit the EP controller the Biometric reader is installed under
4. Select the Biometrics tab
5. Enter the maximum number of biometrics the EP will store
   The EP card capacity will decrease as the maximum number of templates increases.
6. Select the Default security threshold
   • The default threshold determines the ratio of false rejects to false accepts.
     • Highest – Most Secure
     • Medium – Default Settings
     • Lowest – Least Secure
7. If needed, check the Store security threshold per user checkbox if needed
   • When checked, the default security threshold for the SCP can be overridden on a per Cardholder basis. This option is useful when environmental conditions may require certain card holders to have a less secure security threshold to allow biometric verification when dealing with dirty or harsh environments.
8. Click Save
9. Within the Hardware Tree, expand SCPs | SIOs
10. Edit the SIO the Biometric Gateway is addressed for
11. Select the model Bioscrypt Gateway
12. Select (check) the option Device Installed
13. Select the Options tab
14. Select how many 4G readers are uniquely addressed and connected to the Biometric Gateway
15. Click Save
16. Within the Hardware Tree, select Installed Readers
17. Edit the reader that the external reader is attached to
18. Select the Biometrics tab
19. Select the correct 4G reader from the Associated Biometric Reader list
20. Check the box Require Biometric Verification
21. Click Save

---