In observance of Thanksgiving, RS2 Technologies will close at 12:00 PM CDT on November 21st and remain closed on November 22nd & 23rd.

Configuring The 2g For Access It! Lite.NET


Overview

In order for the 2g panel to communicate with Access It! Lite.NET, a new revision of firmware is required. This document outlines the steps needed to download the new firmware to the 2g. Access It! Lite.NET must already be installed on the machine prior to following the steps below.

2gLE/2gE (TCP)

  1. Set S1- Address Dip switches 5, 6, and 7 ON and switches 1, 2, 3, 4, and 8 OFF
  2. Open jumper JP1
  3. Connect panel to network using network cable
    It is recommended to use a laptop and attach the panel using a crossover cable.
  4. Apply power to the board
  5. Open the Panel Utility found off of Start | Programs | Access It! Lite.NET | Utilities
  6. In the MAC Address field enter the MAC address of the NIC card
  7. In the IP Address field, enter the desired IP address for the 2gE/2gLE
    The computer may need to be manually configured to be in the same IP range as the desired IP address for the 2gE/2gLE.
  8. In the Gateway IP Address, enter the desired gateway IP address
  9. In the subnet Mask field, select the correct subnet mask being used
  10. In the panel type drop list, select 2gE/2gLE
  11. If the web server needs to disabled, check Disable Web Server (recommended)
  12. If a password needs to be assigned for a telnet session enter the desired password
    If a password does not need to be assigned for a telnet session, leave field blank.
  13. Click Set Configuration
    If error occurs, disable firewall and try again.
  14. When complete, a message box stating Configuration Set! will be displayed
  15. Click OK
  16. Select the Panel Diagnostics tab
  17. In the Panel Type drop list, select 2g
  18. In the Comm Type drop list, select TCP/IP
  19. In the Address field, set address to 0
  20. In the IP Address field, enter the newly programmed IP address of the 2gE/2gLE
  21. Click the Attach option
  22. Once attached, click Download Firmware
  23. Select the file ScpA3120.crc
  24. Click Open
  25. During the download, the word Downloading will be displayed in the lower left corner
    The Firmware download can take up to 10 minutes to complete
  26. Once the status displays Idle Click the Detach option
  27. Close the Panel Utility

The 2g is now ready to be used with Access It! Lite.NET.

2g/2gL (Hardwired)

  1. Set S1- Address Dip switches 6 and 7 ON and switches 1, 2, 3, 4, 5, and 8 OFF
  2. Close jumper JP1
  3. Connect panel to the computers comm port
  4. Apply power to the board
  5. Open the Panel Utility found off of Start | Programs | Access It! Lite.NET | Utilities
  6. Select the Panel Diagnostics tab
  7. In the Panel Type drop list, select 2g
  8. In the Comm Type drop list, select Hardwired
  9. In the Address field, set address to 0
  10. In the Comm Port field, enter the comm port the 2g/2gL is wired to
  11. In the Baud Rate drop list, select 38400
  12. Click the Attach option
  13. Once attached, click Download Firmware
  14. Select the file ScpA3120.crc
  15. Click Open
  16. During the download, the word Downloading will be displayed in the lower left corner
    The Firmware download can take up to 10 minutes to complete
  17. Once the status displays Idle Click the Detach option
  18. Close the Panel Utility

The 2g is now ready to be used with Access It! Lite.NET.


  • 13
  • 14-Mar-2018
  • 5005 Views
    Tags
  • (1)