Aperio AH20 Hub
Overview
The ASSA ABLOY AH20 Hub allows for a single Aperio lockset to communicate to an Aperio Hub via a 2.4 GHz signal. Prior to connecting the AH20 Hub to the appropriate reader port, it must first be pre-programmed and have a lock associated to it using the Aperio Programming Application.
For more information on the Aperio Programming Application, please contact (800) 810-WIRE.
Hardware Configuration
Wiring
The Aperio AH20 Hub communicates via a Wiegand signal to the reader port of the SCP/SIO.
| Aperio Hub | Reader Port |
| DATA 1 | CLK/D1 |
| DATA 0 | DAT/D0 |
| GREEN | LED |
| GND | GND |
| 8-24VDC | VO |
More Information
- As the hub will output a Wiegand signal to the reader port of the SCP/SIO, use of the AH20 is entirely transparent to the Mercury hardware.
- Dip Switch Number 1 on AH20 controls use of LED Red signal for access decision. If landing Aperio Hub Connector GREEN on LED, this dipswitch should be set to OFF.
- 105
- 14-Jan-2019
- 4799 Views
-
Share this
- Google Plus
Related Articles
- 2g Dialup Configuration
- 2g Quick Reference Sheets
- 50 Bit Wiegand RBH50 Card Format
- Aperio LED Lock Codes
- ASSA ABLOY IP Lockset Ports
- BF-430 Serial to Ethernet Convertor
- Capturing And Submitting A Debug File
- Changing SCP/2gE Channel 1 Settings Using Telnet
- Changing The Default Username And Password Of The EP Series Panels
- Changing The IP Address Of A 2g Or SCP Using Telnet
- Configuring Access It! Universal.NET For Casi Transition Proximity Readers
- Configuring an EP Series Controller for Access It! Universal.NET
- Configuring an LP Series Controller for Access It! Universal
- Configuring The MR-51e For Access It! Lite.NET
- Configuring The MR-51e For Access It! Universal
- Configuring Universal To Utilize The Casi Proximity Readers
- Distributed Hardware Firmware Advisory
- ENGAGE Devices Factory Reset
- EP-1501 / MR-51e PoE Recommendations
- EP-2500 Redundant Communication
- EP Controllers - Security Settings
- EP/LP Controller Power State Reports Fault
- EP / LP Series Web Logins
- EP/MINI-SCP Dialup Configuration
- EP Panel Capacities
- EP Series IP Client Configuration
- Error Input Fault
- Farpointe Data - Delta3 LED Status
- HID 4033-BGN
- ID Card Sizes
- iSTAR Hardware Quick Reference
- Lenel To RS2 Cross Reference
- LifeSafety Power Supply Integrations
- Low Battery Notification
- Low Voltage Protection On HID Smart Card Readers
- LP / EP / SCP Quick Reference Sheets
- LP Series Legacy Mode
- LP Series Legacy Mode - Incorrect Date and Time
- M5 Hardware Quick Reference
- Manually Updating SCP / EP Firmware
- Mercury EP Controller Web Page Loads Slowly
- Modifying The Windows Hosts File To Resolve DNS Issues
- MR-51e Address Tool
- MR-DT Quick Reference And EP Series Guide
- NCL-12UL Hardware Installation Manual
- NCL Quick Reference Sheet
- No Reader Power - LP1502, LP4502, & MR-52-Series 3 Boards
- On Board Backup Battery Lifespan
- PAM V5 LED control
- Power Over Ethernet (PoE) Auxiliary Power Output
- Programming a NIC card with the Panel Utility
- Reader Power Select Configuration Options For LP4502, LP1502 & MR-52-Series 3 Boards
- Resetting An OEM Code To Resolve Invalid OEM Code Error Message
- RS2 RMA Procedures
- RS-485 Cable Length
- SCP / EP 128 Bit AES Encryption
- SCP / EP 256 AES Encryption
- SCP incorrectly displays Normal/Encrypted
- SCP Web Server Configuration
- SNMP Support
- Suggested Wiring Spcifications
- Unlocking A 2gL/2gLE Panel
- Updating SCP Firmware Using the Panel Utility
- Updating SIO Firmware
- Vanderbilt Integration
- Voltage Output (DC) For RS2-LP-1
- WAN IP Client Configuration
- Wiegand Reader Cable Length